[Solved] Problem with "Change default values"

CADCAM machining solution: mill-turn centers, milling and turning, kinematics, fixtures, topology recognition, tool library, manufacturing schedules, realistic simulation, workshop sheets, post-processors and DNC...

Moderators: remi77, Daniel, jacs

User avatar
remi77
Administator
Administator
Posts: 298
Joined: Thu Feb 22, 2007 10:05 am
Contact:

[Solved] Problem with "Change default values"

Unread post by remi77 » Mon Nov 24, 2008 8:28 am

Hi to all,

Since TopSolid 'Cam patch 6.9.240, I have problem with the function "Change default values".
I have checked that my default files is "ZmiOpuser".
But if I choose "sweeping mode" with a sweep direction of 180°. Those changes are not saved.
Stranger, check my ZmiOpuser below (it was empty at the beginning) :

Code: Select all

[cent_axial] 
# user_depth = 
[drill_axial] 
# user_depth = 
[spot_facing_axial] 
# user_depth = 
[point_axial] 
# user_depth = 
[ream_axial] 
# user_depth = 
[tapp_axial] 
# user_depth = 
[counter_sinking_axial] 
# user_depth = 
[cent_radial] 
# user_depth = 
[counter_sinking_radial] 
# user_depth = 
[drill_radial] 
# user_depth = 
[spot_facing_radial] 
# user_depth = 
[point_radial] 
# user_depth = 
[ream_radial] 
# user_depth = 
[tapp_radial] 
# user_depth = 
[automatic_phase,f]      // 3dauto finition 
# cret_height_maxi = .global.cret_height      // heigth maxi of #rest (step calcul)      -ALL 
# cret_height_maxi_2 = .global.cret_height      // heigth maxi of crest (step calcul)      -ALL 
[cycle5x] 
# user_depth = 
[center]      // center drill 
# user_depth = 
[pocket center]      // pocket center 
# user_depth = 
[csinking]      // spot Counter Sinking 
# user_depth = 
[spot_facing]      // spot facing 
# user_depth = 
[gundrilling]      // gundrilling 
# user_depth = 
[cboring]      // mill_hole 
# user_depth = 
[point]      // point 
# user_depth = 
[pocket pointer]      // pocket pointer 
# user_depth = 
[drill]      // drill 
# user_depth = 
[pocket drill]      // pocket drill 
# user_depth = 
[leading_spot_facing]      // pull spot facing 
# user_depth = 
[ream]      // ream 
# user_depth = 
[tapp]      // tapp 
# user_depth = 
Even with a good ZmiOpUser file, the prefernces are not loaded.

So if you've got any suggestions... :D

See you

Rémi :wink:
Last edited by remi77 on Mon Nov 24, 2008 10:36 am, edited 1 time in total.

Liam
Private
Private
Posts: 8
Joined: Thu Feb 22, 2007 11:23 am
Location: Villeurbanne
Contact:

Unread post by Liam » Mon Nov 24, 2008 9:42 am

Hi !

With TopSolid'Cam 6.9.240 version, you have to download a dll which is available at the same place as the patch :
ftp://ftp.TopSolid.com/Public/TopSolidC ... OpUser.zip

The dll contained in the zip file must be copied in your \missler\v69\bin\ folder.

Normally an email should be sent to everyone about it ... :)

See you !

User avatar
remi77
Administator
Administator
Posts: 298
Joined: Thu Feb 22, 2007 10:05 am
Contact:

Unread post by remi77 » Mon Nov 24, 2008 10:35 am

Hello,

Thanks a lot for this information Liam :D

See you

Rémi :wink:

Post Reply