CAD solution for mold making: slider design, guide rails, jacks,
Moderators: remi77 , jacs , Daniel
0 Replies
254349 Views
Last post by D@vid
Tue Sep 30, 2014 5:48 pm
trimming return pins
Replies: 12
by
Jimmy »
Thu Dec 06, 2007 6:48 pm
First post
my return pins won't trim up to the surface. I have 6 return pins and was able to trim only 1 out of 6. I dropped a ucs at the center and depth of...
Last post
Another way is
12 Replies
11992 Views
Last post by RICHARD LALONDE
Mon Dec 10, 2007 4:21 pm
driving elements come back
Replies: 3
by
Jimmy »
Thu Dec 06, 2007 8:20 pm
First post
one more thing. I hid all of my driving elements so it's easier to see. Then I go into visualization and shut off all the items in my components...
Last post
Usually the location dimensions & UCS's used to insert mold components (like a bolt) will unblank themselves when you use mold visualization. The...
3 Replies
5803 Views
Last post by Larry M.
Fri Dec 07, 2007 1:50 pm
Screw section
Replies: 3
by
RICHARD LALONDE »
Wed Nov 28, 2007 11:11 pm
First post
This is a link to the French Forum to refer to all picture
Last post
I'm lucky because I could discuss on both forum,
3 Replies
5467 Views
Last post by RICHARD LALONDE
Thu Nov 29, 2007 5:11 pm
TopSolid'Mold Tutorial
Replies: 17
by
Bill »
Tue Mar 13, 2007 3:05 pm
First post
Hey Matt,
Last post
Hi TopSolid users,
17 Replies
27050 Views
Last post by D@vid
Fri Nov 23, 2007 3:33 pm
Hey! Where did it go? (unite question)
Replies: 4
by
Jenny »
Wed Nov 07, 2007 2:02 pm
First post
I would like to unite my core block bottom (original block created after parting line) to my core mold base. The problem I'm experiencing is that any...
Last post
Hello,
4 Replies
6713 Views
Last post by jehronimo
Wed Nov 07, 2007 5:12 pm
[Solved] DME Inch and PCS Locating Rings Position is Wrong
Replies: 8
by
TopSolid2007 »
Fri Sep 21, 2007 5:26 pm
First post
DME Inch and PCS Inch Locating Rings Position is Wrong.
Last post
Hello Richard,
8 Replies
9040 Views
Last post by Bill
Tue Nov 06, 2007 5:31 pm
[Solved] Multi-cavity issue
Replies: 3
by
Jenny »
Tue Oct 30, 2007 4:56 pm
First post
I want to create a two cavity mold using the multi-cavity function.
Last post
Hello Jenny!
3 Replies
5388 Views
Last post by Bill
Fri Nov 02, 2007 6:08 pm
Shift part
Replies: 3
by
Stockwell »
Wed Oct 31, 2007 1:47 pm
First post
Going to be alot of questions I am sure here as Oldcastle, Ontario starts using Top Solid for Mold design.
Last post
Got it relocated guys, thanks for looking at the file Larry!
3 Replies
5356 Views
Last post by Stockwell
Wed Oct 31, 2007 4:08 pm
[Solved] Angle pin problem
Replies: 2
by
RICHARD LALONDE »
Thu Oct 25, 2007 3:19 pm
First post
Does some one have problem to place an angle pin ?
Last post
Effectively the first time it was because my cam travel was on the wrong side. But after I replace the datum of my slide and not redo the complete...
2 Replies
4681 Views
Last post by RICHARD LALONDE
Mon Oct 29, 2007 6:46 pm
[Solved] HASCO INCH Mold Bases are wrong.
Replies: 3
by
Larry M. »
Sat Sep 15, 2007 2:58 am
First post
All, and I do mean all, of the Hasco Inch Library mold bases use the wrong Pin and bushings. Hasco always uses a stepped Leader Pin. So when they...
Last post
Just so you know, these libary problems have been reported and corrections will be worked on over the coming months. Just wanted to let you guys know...
3 Replies
5814 Views
Last post by Bill
Tue Oct 02, 2007 9:17 pm
Forum permissions
You cannot post new topics in this forumcannot reply to topics in this forumcannot edit your posts in this forumcannot delete your posts in this forumcannot post attachments in this forum
